Kategorier

Slotted bone nut for acoustic guitar, 1-11/16" x 3/16" x 11/32".

Compensated bone saddle for Taylor® guitars, 2-13/16" x 1/8" x 3/8".

CTS 1 Meg solid shaft audio pot - 1 Meg ohm audio taper potentiometer CTS, solid shaft, with hardware.

Ebony bridge pin set, slotted (6 pcs.), no dot, with Ebony end pin.

input cup jack plate for Telecaster®, nickel Cup jack plate for Tele®, with clip.

250K audio potentiometer, standard length bushing .375", 3/8" diameter Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

250K linear potentiometer, standard length bushing .375", 3/8" diameter Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

500K audio potentiometer, standard length bushing .375", 3/8" diameter Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

500K linear potentiometer, standard length bushing .375", 3/8" diameter Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.

push-pull 500K audio potentiometer, standard length bushing .375", 3/8" diameter

push-pull 500K linear potentiometer, standard length bushing .375", 3/8" diameter

Mekanikk for klassisk gitar fra Altamira i høy kvalitet. Gullfarget med perlehvite ører.

Mekanikk for klassisk gitar fra Altamira i høy kvalitet. Nickelfarget med kremhvite ører.

ALTAMIRA N 100 E Med Fishman pickupsystem m/tuner og balansert utgang

Bass String Guide Round with Screw, Nickel

Bone nut blank 2-1/16" x 3/8" x 1/4" slant cut.

Slotted bone nut with radiused bottom for Fender ®, 1-11/16" x 1/4" x 1/8".

Bone nut shaped for Martin® guitars with slanted bottom and sides

Slotted bone nut for acoustic guitar, 1-11/16" x 3/16" x 11/32".

Bone nut for J.Bass ®, with string slots, 1-9/16" x 1/8" x 3/16".

slotted bone nut for Epiphone® 42,86x6,36x9,5 mm Bone nut for Epiphone ® guitars with string slots, 1-11/16" x 1/4" x 3/8".

slotted bone nut blank for Martin® 44x5,7x9,3 mm Slotted bone nut for Martin ® guitars with angled sides and bottom, 3/4" width.

tremolo springs, 3pcs

bridge saddles, nickel, 6pcs

Bridge Saddles Tilt-Compensated(set of 3) with Screws & Springs for Telecaster®, Brass

Compensated bone saddle for acoustic guitar, radiused top 3" x 7/64" x 11/32, bleached bone.

Compensated bone saddle for acoustic guitar, radiused top 3" x 7/64" x 11/32, unbleached bone.

Compensated bone saddle for Gibson ® guitars, 2-13/16" x 1/8" x 15/32".

saddle for classical guitar, compensated, bone

CTS 1 Meg audio taper pot 1 Meg ohm audio taper potentiometer CTS, split, knurled shaft, with hardware.

On-On-On miniswitch, DPDT, chrome

250K Mini Pot, Audio Taper, 3/8" Long Bushing, Split, Knurled Shaft with Nut and Washer

Brass Sleeves - Convert Split Shaft Pot to Solid Shaft Pot

On-On Slide Switch by Switchcraft, for Jazzmaster® and Jaguar® guitars. Black Knob, with screws. Requires 3/4" cavity depth and 5/16" x 9/16" slot . 1-1/8" screw spacing

Switchcraft On-Off-On slide switch, black On-Off-On slide switch, Switchcraft, for Mustang®, black, with screws.

Switchcraft On-Off-On slide switch, white On-Off-On slide switch, Switchcraft, for Mustang®, white, with screws.

250K push / pull audio taper potentiometer. Threaded portion is approximately 9.35 mm diameter. 35mm from bottom of pot to top of threaded portion. Pulls out 4 mm. Includes nut and washer.

5-way Oak Grigsby super switch, 1 wafer, 2 pole, with stainless steel screws

ALLPARTS EP-0686-000 CTS 500K Long Split Shaft Audio Pot - 500K Audio Pot, 3/4 Long Threaded Bushing, CTS, split, knurled shaft with nut, lock and dress washer. Threaded bushing is 3/4" tall. Popular replacement pot for many Gibson® Les Paul® guitars.

3-Way blade switch, with screws, Tritan.

5-Way blade switch, with screws, Tritan.

250K ohm audio pot, CTS, vintage style, split knurled shaft with nut, lock & dress washer.

500K ohm audio pot, CTS, vintage style, split knurled shaft with nut, lock & dress washer.

250K Audio Pot, 3/4 Long Threaded Bushing, CTS, 24 spline split shaft, with hardware

300K Linear Pot, 3/4" Long Threaded Bushing, CTS, Split Shaft, with hardware

Pickguard Screws Phillips Head, Nickel, #4 x 1/2"

Pickguard screws Gibson® size, phillips head, #3 x 3/8" (9,5mm).

Tuning key screws, small size for enclosed keys, #2 x 3/8" (9,5 mm) long.

Bridge height screws for bass or Tele ®, slot head, stainless steel, #6 - 32 x 1/2" (13 mm).

European solid spruce top Bamboo back and sides Bamboo neck Bamboo fingerboard and bridge Pinless bridge design Maple body binding Scale length 648mm Nut width 45mm Adamas strings 1818NU .012- .053, GEWA 664.650 Bonoid nut and bridge inlay Open pore matt finish, white top Matt chrome machine head Cutaway Applause AFX-3T preamp with built-in speaker and effects (reverb, chorus, delay)

Plastic washers for guitar tuning keys. Placed between button and housing. Inside diameter 3.75 mm, outside 6.5 mm.

Plastic washers for bass guitar tuning keys. Placed between button and housing. Inside diameter 4.5 mm, outside 7 mm.

Black Mountain Thumb Picks are built for musicians who enjoy playing with their fingers (fingerstyle) but also enjoy playing with a pick (flatpicking). Players love the Black Mountain Pick because it feels like a regular guitar pick, but it also feels like a traditional thumb pick. HANDMADE IN CANADA

Justerbart Strengetre til Blade Gitarer

– Stemmeskruer for 12-strengs gitar – Dobbelborrede metallstolper – 125 mm – Plastknapper